Mini PC Case Switching Mode Power Supply 200Watt , 47 Hz - 63 Hz Frequency

 

Mini PC Case Switching Mode Power Supply 200Watt , 47 Hz - 63 Hz Frequency

 

 

Competitive Advantages:

1. short-circuit protection

2. OEM/ODM welcome

3. thermal protection 

4. Professional mini itx case manufacturerover

5. current protection 

6. over-voltage protection

Why Realan:

We are a very professional manufacturer for mini computer cases and power supplies, with the rich experience for over 10 years of developing and producing pc cases. Determination achieves quality, Realan is always keeping the production philosophy that doing by heart, win to win, providing the higher products value cooperation. And our products have been exported to East Asia, Southeast Asia, Middle East, North America, South America, Europe, Africa, Australia and other countries. 
Please don't hesitate to contact us if you have any questions or concerns before or after your purchase. We are committed to your 100% satisfaction.

 

Detailed Specification:

 

1.0 INPUT

1.1 VOLTAGE

 

Min.	Normal	Max.	Unit
180	220	260	Vac
90	110	130	Vac

 

1.2 FREQUENCY

47-63 Hz

1.3 CURRENT

 

Max. 2.5A /220Vac

Max.5A /110Vac

1.4 INRUSH CURRENT

60A/220V at 25℃COLD START

1.5 EFFICIENCY

MIN65%AT FULL LOAD 220Vac 50Hz

2.0 OUTPUT

2.1 OUTPUT POWER

200W (MAX).

2.2 VOLTAGE

 

	+5V	+12V	-12V	+3.3V	+5Vsb
MAX LOAD	10A	10A	0.3A	8A	2A
MIN LOAD	1.5A	0.3A	0A	0A	0A
Regulation	± 5%	± 5%	± 10%	± 5%	± 5%
Ripple	50mV	120mV	300mV	50mV	50mV
Noise	100mV	240mV	360mV	100mV	100mV

 

NOTE:

1, The continuous max. DC output power shall not exceed 200W.And+5V,+3.3V total output power must not exceed 100W.

2, A 0.1uF ceramic disk capacitor & 10uF electrolytic (low ESR) capacitor should be putacross the output terminals during ripple & noise measure. The oscillo-scope bandwidth set at 20MHz withco-axial probe.

3, Regulation load must within 30% to 70% of maximum load.

4, AMBIENT TEMPERATURE 25℃.

3.0 PROTECTION

3.1 OVER LOAD PROTECTION

3.1.1 120-160% of maximum power.

3.2 SHORT CIRCUIT PROTECTION

All output to ground.

NOTE :After protection active all output will shut down .After shut down the power supply shall

return to normal operation.only after the fault has been removed and the remote signal

reset for a minimum 1 second (or the AC remove for 10 second).

4.0 TIMING SEQUENCE

4.1 TURN ON TIME

900mS MAX

4.2 P.G Delay time

100~500mS

4.3 P.F time

1mS MIN.

4.4 Hold up time.

15mS MIN.

5.0 TEMPERATURE CHARACTORISTICS

5.1 OPERATION AMBIENT :

+10 to +40℃.

20~85%

5.2 NON-OPERATION AMBIENT:

-40℃to +70℃.

10~90%

6.0 SAFETY REQUIREMENT

6.1 HI-POT TEST

Vac =1500 Vac Current limit 10mA

6.2 GROUNDING TEST

 

R<100mOhm

Condition

I=24Aac

6.3 Isolation test

 

R>2MOhm

Condition

400VDC

7.0 ELECTROMAGNETIC COMPATIBILITY (Optional )

7.1 Meet with the EMI standards.

8.0 Burn-in

Full load,2 Hour .