Place of Origin: | CHINA |
Model Number: | POE-A0502 |
Transmission Rate: | 10M/100Mbps |
---|---|
Protocol Standard: | Non-IEEE802.3 |
Delivery Time: | 3-30days |
---|
POE Switching Power Supply & Adapter
POE-A0502
Over View:
POE (Power Over Ethernet) is a technology solution that, under the case of no any change for current Ethernet Cat5 wiring/cabling infrastructure, not only transfer data signal but also provide direct current power for some IP based terminal device (like IP telephony, Wireless LAN access point, Network camera, etc.).
POE technology can minimize the cost while ensuring the normal operation of the existing network and the safety of the existing structured cabling.
POE adapter provide a power solution for the related device, it can supply power and simultaneously be a media for data transfer in anywhere there is a cat5 cable.
POE also known as power system based on local area network (POL, Power over LAN) or Active Ethernet, sometimes it is briefly called Power Over Ethernet, this is the latest standard specification of transferring data and delivering power while taking advantage of existing standard Ethernet transmission cable, and preserve the compatibility between user and the existing Ethernet system.
IEEE 802.3 is new standard of POE in the base of Ethernet power system, which add related standard in power over network cable directly through IEEE 802.3, it’s an extension of existing Ethernet standard, and it is also the first international standard in power distribution.
POE principle (Power over network cable)
There are 4 pairs of twisted pair for the standard CAT5 network cable, but there are only 2 pairs ones are adapted/applied in 10M BASE-T and 100M BASE-T. IEEE802.3 allows two solutions, when power delivered through free pin, PIN 4&5 connect positive”+”, PIN 7&8 connect negative”-”, while power delivered through data pin, add DC power on the central point of the transmission transformer, without affecting the data transfer. In this case, pin 1&2 and pin 3&6 are at any polarity. IEEE802.3 standard will not allow above two applications happen at the same time. The PSE(Power Source Equipment) provide only one power solution, but the PD(Powered Device) must be adapted to above two application solutions at the same time.
Benefits of POE
1. Cost saving. As it’s just one instead of two pieces of net cable for the installation. PD, in most cases, are installed at where is hard to access AC power. Along with increasing device connected to Ethernet, if there is no need to provide local power for device, it will greatly reduce the cost of installation and simplify the management.
2. It’s easy to install and manage. It allows users to use original device and POE device together on internet automatically and safely, which make rooms for original device coexist with Ethernet cable.
3. It’s safety. As POE supply terminal device just provide power for those device that need power. The Ethernet cable will generate voltage only when it’s connected between POE and Powered Device, so it have eliminated the dangerous of power leakage on cable line.
4. It’s easy to manage network equipment.
General Specification:
Model:POE-A0502
Input:AC100-240V, 50-60Hz
Output:DC5V, 2A; 10W
Key Feature:
1. Strong resistance of interference, high reliability
2. Low DC ripple, high efficiency, low standby power consumption, lower heating value, natural cooling, long service life
3. Broad input voltage range (100-240VAC), conform to multinational use standard.
4. Excellent insulating performance, higher dielectric strength.
5. Good load capacity, constant current & constant voltage, wider adaptive range, over-voltage protection for input and output, short-cut protection, over-current protection.
6. The shell is made of flame resisted engineering plastic, which greatly improve the equipment using safety
7. Transmission Distance: Max.20 meters (CAT 5 or better cable). It specifically depends on the quality of network cable, supply voltage and adaptability of power device for voltage. The higher quality of network cable, the voltage drop will be less, and the effective power distance will be further accordingly.
Technical Specification
Input Characteristics |
Direct Feeding=Plug and supplying power, supplying power directly without advanced detection for Power Device (PD). |
Input Voltage/Frequency |
AC100-240V; 50-60Hz |
Input Adjusting Range |
AC 90-264V; 47Hz~63Hz |
Output Voltage/Current |
5V, 2A; 10W; Max. 12.5W |
Output Voltage Regulation |
-5VDC±2% |
Load Regulation |
-5VDC±1% |
DC Output Broadband Noise Voltage |
3.4kHz~150kHz ≤50mv |
Network Port Mark |
Data&Power Out=Power pin (4/5 “+” & 7/8 “-”) + Data pin (12/36) Data In=Data pin (12/36) |
Transmission Rate |
10M/100Mbps |
Transmission Distance |
Max. 20 meters |
LED Power Indicator |
Color: Blue/Green (optional) |
Indicator On: Power in normal working condition; |
|
Indicator Off: Power supply failure; |
|
Note: When the power in normal working condition, after connecting network cable, the indicator off means it’s in over-load protection or shortcut status, it should be the requiring power of powered device is too high, network cable is shortcut or the powered device is broken. |
|
System Reliability |
MTBF>100khours |
Operating Environment |
1. Operating/Ambient Temperature: -10℃~50℃ |
2. Relative Humidity: 5%~90%RH |
|
3. Operating and Storing Place: Ventilation and heat dissipation, Clean, No conductive dust, No corrosive gas |
|
4. Place of No dangerous of explosion |
|
Safety Assurance |
Conducted Emission(CE) and Radiated Emission(RE) compliant with EN60950, CE, FCC standard |
Dimension/Weight |
83.5mm×47mm×53.7mm; 65g |
Power Plug |
EU/US/UK/AU Plug are available |
Lightning Protection |
AC Input can stand 5 times positive & negative 5KV, 8/20uS instantaneous current wave, lasting 1 minutes each time. The lightning protection circuit of the power adapter have invalidation alarming function and protective components like glass protective tube |
Application |
This is ordinary switching power supply, great protective performance, superior stability and adaptability connecting with power device, its scope of application include security surveillance, wireless access point, electrical machine, communication equipment, health care products and those POE supported equipment. |
Warranty |
One year after delivery |
Contact Person: Mr. li
Tel: 56966398
Fax: 86-20-5696-5696
Address: 4th Floor, No. 174, Binjiang Xi Road, Haizhu District, shenzhen,Guangdong,China(Mainland)
Factory Address:4th Floor, No. 174, Binjiang Xi Road, Haizhu District, shenzhen,Guangdong,China(Mainland)